e0f54a37cd
* forced connection attempt is now hardcoded in Sodaq_nbIOT::connectSocket() * udp send recieve now works, may contain bugs on fast multiple incoming messages, have to check if this can be an issue or not
87 lines
2.0 KiB
C++
87 lines
2.0 KiB
C++
#include <Arduino.h>
|
|
|
|
#if defined(ARDUINO_AVR_LEONARDO)
|
|
/* Arduino Leonardo + SODAQ NB-IoT Shield */
|
|
#define DEBUG_STREAM Serial
|
|
#define MODEM_STREAM Serial1
|
|
#define powerPin 7
|
|
|
|
#elif defined(ARDUINO_SODAQ_EXPLORER)
|
|
/* SODAQ Explorer + SODAQ NB-IoT Shield */
|
|
#define DEBUG_STREAM SerialUSB
|
|
#define MODEM_STREAM Serial
|
|
#define powerPin 7
|
|
|
|
#elif defined(ARDUINO_SAM_ZERO)
|
|
/* Arduino Zero / M0 + SODAQ NB-IoT Shield */
|
|
#define DEBUG_STREAM SerialUSB
|
|
#define MODEM_STREAM Serial1
|
|
#define powerPin 7
|
|
|
|
#elif defined(ARDUINO_SODAQ_AUTONOMO)
|
|
/* SODAQ AUTONOMO + SODAQ NB-IoT Bee */
|
|
#define DEBUG_STREAM SerialUSB
|
|
#define MODEM_STREAM Serial1
|
|
#define powerPin BEE_VCC
|
|
#define enablePin BEEDTR
|
|
|
|
#elif defined(ARDUINO_AVR_SODAQ_MBILI)
|
|
/* SODAQ MBILI + SODAQ NB-IoT Bee */
|
|
#define DEBUG_STREAM Serial
|
|
#define MODEM_STREAM Serial1
|
|
#define enablePin BEEDTR
|
|
|
|
#elif defined(ARDUINO_SODAQ_SARA)
|
|
/* SODAQ SARA */
|
|
#define DEBUG_STREAM SerialUSB
|
|
#define MODEM_STREAM Serial1
|
|
#define powerPin SARA_ENABLE
|
|
#define enablePin SARA_TX_ENABLE
|
|
|
|
#else
|
|
#error "Please use one of the listed boards or add your board."
|
|
#endif
|
|
|
|
unsigned long baud = 9600; //start at 9600 allow the USB port to change the Baudrate
|
|
|
|
void setup()
|
|
{
|
|
#ifdef powerPin
|
|
// Turn the nb-iot module on
|
|
pinMode(powerPin, OUTPUT);
|
|
digitalWrite(powerPin, HIGH);
|
|
#endif
|
|
|
|
#ifdef enablePin
|
|
// Set state to active
|
|
pinMode(enablePin, OUTPUT);
|
|
digitalWrite(enablePin, HIGH);
|
|
#endif // enablePin
|
|
|
|
// Start communication
|
|
DEBUG_STREAM.begin(baud);
|
|
MODEM_STREAM.begin(baud);
|
|
}
|
|
|
|
// Forward every message to the other serial
|
|
void loop()
|
|
{
|
|
while (DEBUG_STREAM.available())
|
|
{
|
|
MODEM_STREAM.write(DEBUG_STREAM.read());
|
|
}
|
|
|
|
while (MODEM_STREAM.available())
|
|
{
|
|
DEBUG_STREAM.write(MODEM_STREAM.read());
|
|
}
|
|
|
|
#ifndef ARDUINO_AVR_SODAQ_MBILI
|
|
// check if the USB virtual serial wants a new baud rate
|
|
if (DEBUG_STREAM.baud() != baud) {
|
|
baud = DEBUG_STREAM.baud();
|
|
MODEM_STREAM.begin(baud);
|
|
}
|
|
#endif // !ARDUINO_AVR_SODAQ_MBILI
|
|
}
|